Autor |
Mensaje
|
zabit |
Publicado: Sab Feb 17, 2007 2:25 am Título del mensaje: Parametros de mi Bios que desconozco |
|
|
Registrado: 28 Jul 2006 Mensajes: 264
|
vamos a preguntar esto para los que saben de verdad
en mi An8-sli vi parametros de la bios que nunca supe si me sirven.
igual quiero saber de que se trata cada uno.
1Pic-DDR REF Voltaje que tiene opcion de cambios en + - 10mv a + -70mv que no se que es
2Pic-Tambien en CPU REF Voltaje los mismos cambios tiene + - 10mv a + - 70mv
yo el voltaje de las Tccd las cambio donde dice DDR SDRAM Voltaje
pero esos DDR2 de donde salieron??
3Pic- DDR VTT Voltaje y muestra varios voltajes a la derecha
agradezco desde ya por que se que me van quitar la intriga
(despues pego mas pics de timing memos que eso es otro kilombete aparte ) _________________
abit-AN8-SLI
TT Ruby Orb *1200Rpm
AMD-Toledo Sin IHS 3800X2@2700Mzh 1.450V
OCZ 2X1GB GX-XTC @450mhz 2,8V 2.5-3-3-6 1T
XFX 8600GT xxx Edition 700/850
Seagate320 NCQ
VTB Master 550W
http://valid.x86-secret.com/show_oc.php?id=311975 |
|
Volver arriba |
|
|
|
|
|
jona101 |
Publicado: Sab Feb 17, 2007 3:46 am Título del mensaje: |
|
|
Staff Tortugahard
Registrado: 10 Sep 2006 Mensajes: 774 Ubicación: Santa Fe, Capital
|
Bueno el DDR Ref. Voltage es en español Voltaje de referencia de DDR.. la funcion es de aumentar el voltaje en milivoltios... como veo te aparecen para aumentar o disminuir de a 10mV q es lo mismo 0.010 V
Bueno en el CPU Ref Voltage es lo mismo
Ni idea lo q es ddr vtt voltage.... estoy googleando pero no encontre nada _________________
|
|
Volver arriba |
|
|
zabit |
Publicado: Sab Feb 17, 2007 11:34 am Título del mensaje: |
|
|
Registrado: 28 Jul 2006 Mensajes: 264
|
gracias jona101 ,,.osea que es para subir minimamente el voltaje de las memos o el cpu en menos o mas ??
me gusto la opcion si es asi por que podes retocar un pelito los voltajes y no de 0.25V que es bastante aveces
Si!, eso del DDR 2 ke sera no?tendre un p4 espiando mi AMD? _________________
abit-AN8-SLI
TT Ruby Orb *1200Rpm
AMD-Toledo Sin IHS 3800X2@2700Mzh 1.450V
OCZ 2X1GB GX-XTC @450mhz 2,8V 2.5-3-3-6 1T
XFX 8600GT xxx Edition 700/850
Seagate320 NCQ
VTB Master 550W
http://valid.x86-secret.com/show_oc.php?id=311975 |
|
Volver arriba |
|
|
zabit |
Publicado: Dom Feb 25, 2007 2:46 am Título del mensaje: |
|
|
Registrado: 28 Jul 2006 Mensajes: 264
|
sigo rompiendo con las preguntas .y seguro aca varios la deben conocer
tengo varios parametros de los timming de las memos que desconozco..
los mas comunes los se setear,.
uso unas patriot TCCD 2x512 en dual channel
disculpen las fotos pero al no tener camara tuve que sacar con la webcam
estos son los que mas me rompen el bocho ,ese con las flechitas
Y el otro? si yo tengo unas DDR600 donde va puesto por que siempre lo dejo en 333
o es por ke las memos estan en 166 quiere decir?
estos tambien para que seran
MTRR y el otro de 32bit
y estos dos???
Read preamble Value y max.async latency Value
dentro de estos dos tienen numeros que van del 2.0ns al 10ns
para que sirven estos???
_________________
abit-AN8-SLI
TT Ruby Orb *1200Rpm
AMD-Toledo Sin IHS 3800X2@2700Mzh 1.450V
OCZ 2X1GB GX-XTC @450mhz 2,8V 2.5-3-3-6 1T
XFX 8600GT xxx Edition 700/850
Seagate320 NCQ
VTB Master 550W
http://valid.x86-secret.com/show_oc.php?id=311975 |
|
Volver arriba |
|
|
GerardodK |
Publicado: Dom Feb 25, 2007 4:42 am Título del mensaje: |
|
|
Registrado: 21 Nov 2005 Mensajes: 729
|
las memos son DDR, osea Dual Doble Rate. que significa esto? dos ciclos efectivos por ciclo de la memoria, asi es como el 266 anda a 133, el 333 a 166 y el 400 a 200
Sacado de una guia de tccd en dfi nf4
Código: | Read Preamble Time
Settings = Auto, 2.0-9.5 nanoseconds, in 0.5 increments.
From the DFI BIOS: “This BIOS setting specifies the time prior to the max-read DQS return. It shows when the DQS should be turned on.” From an old Samsung memory guide: “Preamble of DQS on reads: DDR SGRAM uses a data strobe signal(s),DQS, to increase performance. The DQS signal is bidirectional which toggles when there is any data transfer from DDR SGRAM to graphic controller or from graphic controller to DDR SGRAM. Prior to a burst of read data, DQS signal transitions from Hi-Z to a valid logic low. This is referred to as the data strobe preamble. This transition from Hi-Z to logic low nominally happens one clock cycle prior to the first edge of valid data.”
Slight Influence on Bandwidth/Stability.
Suggested Settings for DFI: 5.0 ns is the default when set to Auto----suggest starting at 5.0 and then working within this range (4.0-7.0) depending on ram. (Lower = Faster)
Max Async Latency
Settings = Auto, 0-15 in 1.0 increments.
I could not find anything on this particular setting and am not sure what portion of RAM functions it affects. If you have information on this setting, please post and I will update this section. From HiJon89: “The Max Async Latency setting will show its biggest difference in the Everest Latency Test. Going from 8ns to 7ns on my BH-6 made a 1ns difference in Everest Latency. Going from 7ns to 6ns dropped it another 2ns.”
Slight Influence on Bandwidth/Stability.
Suggested Settings for DFI: 7ns is the default----Suggest you start at 7ns and work from there trying 5.0-10.0. From HiJon89: “6ns is very tight, I would recommend running 6ns for UTT or BH-5 but not TCCD. 7ns is looser, good for getting higher clocks on UTT or BH-5. 8ns is pretty loose for UTT or BH-5, but its just right for hitting DDR600 with TCCD. 9ns is very loose even for TCCD and should really only be used to try to hit DDR640+.” (Lower = Faster) | _________________
|
|
Volver arriba |
|
|
zabit |
Publicado: Dom Feb 25, 2007 7:58 pm Título del mensaje: |
|
|
Registrado: 28 Jul 2006 Mensajes: 264
|
gracias Gerardocdk..alfin una ayuda,
igual espero que me saken de las otras dudas _________________
abit-AN8-SLI
TT Ruby Orb *1200Rpm
AMD-Toledo Sin IHS 3800X2@2700Mzh 1.450V
OCZ 2X1GB GX-XTC @450mhz 2,8V 2.5-3-3-6 1T
XFX 8600GT xxx Edition 700/850
Seagate320 NCQ
VTB Master 550W
http://valid.x86-secret.com/show_oc.php?id=311975 |
|
Volver arriba |
|
|
|